Electron Irradiation-Induced Degradation of TiN Thin Films on Quartz and Sapphire Substrates.

In this contribution, we investigated the properties of magnetron-sputtered TiN thin films on sapphire and quartz substrates before and after 5 MeV electron irradiation with a fluence of 7 × 1013 e/cm2. Structural, morphological, optical, and electrical properties were analyzed to observe the impact of electron irradiation on the TiN thin films. The results showed improved electrical properties of the TiN thin films due to high-energy electron irradiation, resulting in increased specific conductivity compared to the as-deposited thin films on both sapphire and quartz substrates. The structural features of the TiN thin films on the sapphire substrate transformed from polycrystalline to amorphous, while the TiN thin films deposited on the quartz substrate remained unchanged. Chemical state analysis indicated changes in the metallic bonding between Ti and N in the deposited TiN on the sapphire substrate, while TiN deposited on the quartz substrate retained its Ti-N bonding. This study provides insights into the effects of electron irradiation on TiN thin films, emphasizing the importance of investigating radiation resistance for the reliable operation of optoelectronic devices and photovoltaic systems in extreme ionizing radiation environments.

High-Performance Wearable Organic Photodetectors by Molecular Design and Green Solvent Processing for Pulse Oximetry and Photoplethysmography.

White-light detection from the visible to the near-infrared region is central to many applications such as high-speed cameras, autonomous vehicles, and wearable electronics. While organic photodetectors (OPDs) are being developed for such applications, several challenges must be overcome to produce scalable high-detectivity OPDs. This includes issues associated with low responsivity, narrow absorption range, and environmentally friendly device fabrication. Here, an OPD system processed from 2-methyltetrahydrofuran (2-MeTHF) sets a record in light detectivity, which is also comparable with commercially available silicon-based photodiodes is reported. The newly designed OPD is employed in wearable devices to monitor heart rate and blood oxygen saturation using a flexible OPD-based finger pulse oximeter. In achieving this, a framework for a detailed understanding of the structure-processing-property relationship in these OPDs is also developed. The bulk heterojunction (BHJ) thin films processed from 2-MeTHF are characterized at different length scales with advanced techniques. The BHJ morphology exhibits optimal intermixing and phase separation of donor and acceptor moieties, which facilitates the charge generation and collection process. Benefitting from high charge carrier mobilities and a low shunt leakage current, the newly developed OPD exhibits a specific detectivity of above 1012  Jones over 400-900 nm, which is higher than those of reference devices processed from chlorobenzene and ortho-xylene.

Interstellar photovoltaics.

The term 'Solar Cell' is commonly used for Photovoltaics that convert light into electrical energy. However, light can be harvested from various sources not limited to the Sun. This work considers the possibility of harvesting photons from different star types, including our closest neighbor star Proxima Centauri. The theoretical efficiency limits of single junction photovoltaic devices are calculated for different star types at a normalized light intensity corresponding to the AM0 spectrum intensity with AM0 = 1361 W/m2. An optimal bandgap of > 12 eV for the hottest O5V star type leads to 47% Shockley-Queisser photoconversion efficiency (SQ PCE), whereas a narrower optimal bandgap of 0.7 eV leads to 23% SQ PCE for the coldest red dwarf M0, M5.5Ve, and M8V type stars. Organic Photovoltaics (OPVs) are the most lightweight solar technology and have the potential to be employed in weight-restricted space applications, including foreseeable interstellar missions. With that in mind, the Sun's G2V spectrum and Proxima Centauri's M5.5Ve spectrum are considered in further detail in combination with two extreme bandgap OPV systems: one narrow bandgap system (PM2:COTIC-4F, Eg = 1.14 eV) and one wide bandgap system (PM6:o-IDTBR, Eg = 1.62 eV). Semi-empirically modeled JV-curves reveal that the absorption characteristics of the PM2:COTIC-4F blend match well with both the G2V and the M5.5Ve spectrum, yielding theoretical PCEs of 22.6% and 12.6%, respectively. In contrast, the PM6:o-IDTBR device shows a theoretical PCE of 18.2% under G2V illumination that drops sharply to 0.9% under M5.5Ve illumination.

Unraveling Device Physics of Dilute-Donor Narrow-Bandgap Organic Solar Cells with Highly Transparent Active Layers.

The charge generation-recombination dynamics in three narrow-bandgap near-IR absorbing nonfullerene (NFA) based organic photovoltaic (OPV) systems with varied donor concentrations of 40%, 30%, and 20% are investigated. The dilution of the polymer donor with visible-range absorption leads to highly transparent active layers with blend average visible transmittance (AVT) values of 64%, 70%, and 77%, respectively. Opaque devices in the optimized highly reproducible device configuration comprising these transparent active layers lead to photoconversion efficiencies (PCEs) of 7.0%, 6.5%, and 4.1%. The investigation of these structures yields quantitative insights into changes in the charge generation, non-geminate charge recombination, and extraction dynamics upon dilution of the donor. Lastly, this study gives an outlook for employing the highly transparent active layers in semitransparent organic photovoltaics (ST-OPVs).

Effect of Electron and Proton Irradiation on Structural and Electronic Properties of Carbon Nanowalls.

In this work, a complex experimental study of the effect of electron and proton ionizing radiation on the properties of carbon nanowalls (CNWs) is carried out using various state-of-the-art materials characterization techniques. CNW layers on quartz substrates were exposed to 5 MeV electron and 1.8 MeV proton irradiation with accumulated fluences of 7 × 1013 e/cm2 and 1012 p/cm2, respectively. It is found that depending on the type of irradiation (electron or proton), the morphology and structural properties of CNWs change; in particular, the wall density decreases, and the sp2 hybridization component increases. The morphological and structural changes in turn lead to changes in the electronic, optical, and electrical characteristics of the material, in particular, change in the work function, improvement in optical transmission, an increase in the surface resistance, and a decrease in the specific conductivity of the CNW films. Lastly, this study highlights the potential of CNWs as nanostructured functional materials for novel high-performance radiation-resistant electronic and optoelectronic devices.

Physical properties of carbon nanowalls synthesized by the ICP-PECVD method vs. the growth time.

Investigation of the physical properties of carbon nanowall (CNW) films is carried out in correlation with the growth time. The structural, electronic, optical and electrical properties of CNW films are investigated using electron microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, UV-Vis spectroscopy, Hall Effect measurement system, Four Point Probing system, and thermoelectric measurements. Shorter growth time results in thinner CNW films with a densely spaced labyrinth structure, while a longer growth time results in thicker CNW films with a petal structure. These changes in morphology further lead to changes in the structural, optical, and electrical properties of the CNW.

Optical Expediency of Back Electrode Materials for Organic Near-Infrared Photodiodes.

Organic semiconductor devices, including organic photodetectors (OPDs) and organic photovoltaics (OPVs), have undergone vast improvements, thanks to the development of non-fullerene acceptors. The absorption range of such NFA-based systems is typically shifted toward the near-infrared (near-IR) region compared to early-generation fullerene-based systems, rendering organic semiconductor devices suitable for near-IR sensing applications. While most efforts are concentrated on the photoactive materials, less attention is paid to the impact of the back electrodes on the device performance. Therefore, this work focuses on the optical expediency of gold (Au), silver (Ag), aluminum (Al), and graphite as back electrode materials in organic optoelectronics. This work shows that the "one size fits all" methodology is not a valid approach for choosing the back electrode material. Instead, considering the active layer absorption, the active layer thickness, and the intended application is necessary. A traditional polymer/fullerene-based system, poly(3-hexylthiophene) with [6,6]-phenyl C61 butyric acid methyl ester (P3HT:PC60BM), and a state-of-the-art narrow-band gap non-fullerene-based system, poly[4,8bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b; 4,5-b']dithiophene-2,6-diyl-alt-(4-(2-ethy-lhexyl)3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-(2-6-diyl)] and 2,2'-((2Z,2'Z)-((5,5'-(4,4-bis(2-ethylhexyl)4H-cyclopenta[1,2-b:5,4-b']dithiophene-2,6-diyl)bis(4-((2ethylhexyl)oxy)thiophene-5,2-diyl))bis(methanylylidene)) bis(5,6-difluoro3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (PCE10:COTIC-4F), are investigated by combining optical transfer matrix modeling simulations with experimentally determined recombination and extraction losses. We find that the narrow-band gap system shows performance gains when employing Au as the back electrode. Furthermore, we show that these performance gains are dependent on active layer thickness, yielding the most significance for thin active layers (<100 nm). Such thin, ultra-narrow-band gap devices are the focus of near-IR sensing applications, highlighting the importance of methodically choosing the back electrode. Lastly, the impact of the back electrode on the OPV device performance is outlined.

Visualization of Charge Transfer from Bacteria to a Self-Doped Conjugated Polymer Electrode Surface Using Conductive Atomic Force Microscopy.

In this work, we aim to provide a better understanding of the reasons behind electron transfer inefficiencies between electrogenic bacteria and the electrode in microbial fuel cells. We do so using a self-doped conjugated polyelectrolyte (CPE) as the electrode surface, onto which Geobacter sulfurreducens is placed, then using conductive atomic force microscopy (C-AFM) to directly visualize and quantify the electrons that are transferring from each bacterium to the electrode, thereby helping us gain a better understanding for the overpotential losses in MFCs. In doing so, we obtain images that show G. sulfurreducens can directly transfer electrons to an electrode surface without the use of pili, and that overpotential losses are likely due to cell death and poor distribution or performance of individual bacterium's OmcB cytochromes. This unique combination of CPEs with C-AFM can also be used for other studies where electron transfer loss mechanisms need to be understood on the nanoscale, allowing for direct visualization of potential issues in these systems.

Organic Electrochemical Transistors Based on the Conjugated Polyelectrolyte PCPDTBT-SO3 K (CPE-K).

PCPDTBT-SO3 K (CPE-K), a conjugated polyelectrolyte, is presented as a mixed conductor material that can be used to fabricate high transconductance accumulation mode organic electrochemical transistors (OECTs). OECTs are utilized in a wide range of applications such as analyte detection, neural interfacing, impedance sensing, and neuromorphic computing. The use of interdigitated contacts to enable high transconductance in a relatively small device area in comparison to standard contacts is demonstrated. Such characteristics are highly desired in applications such as neural-activity sensing, where the device area must be minimized to reduce invasiveness. The physical and electrical properties of CPE-K are fully characterized to allow a direct comparison to other top performing OECT materials. CPE-K demonstrates an electrical performance that is among the best reported in the literature for OECT materials. In addition, CPE-K OECTs operate in the accumulation mode, which allows for much lower energy consumption in comparison to commonly used depletion mode devices.

A High-Performance Solution-Processed Organic Photodetector for Near-Infrared Sensing.

Sensitive detection of near-infrared (NIR) light enables many important applications in both research and industry. Current organic photodetectors suffer from low NIR sensitivity typically due to early absorption cutoff, low responsivity, and/or large dark/noise current under bias. Herein, organic photodetectors based on a novel ultranarrow-bandgap nonfullerene acceptor, CO1-4Cl, are presented, showcasing a remarkable responsivity over 0.5 A W-1 in the NIR spectral region (920-960 nm), which is the highest among organic photodiodes. By effectively delaying the onset of the space charge limited current and suppressing the shunt leakage current, the optimized devices show a large specific detectivity around 1012 Jones for NIR spectral region up to 1010 nm, close to that of a commercial Si photodiode. The presented photodetectors can also be integrated in photoplethysmography for real-time heart-rate monitoring, suggesting its potential for practical applications.

Towards understanding the doping mechanism of organic semiconductors by Lewis acids.

Precise doping of organic semiconductors allows control over the conductivity of these materials, an essential parameter in electronic applications. Although Lewis acids have recently shown promise as dopants for solution-processed polymers, their doping mechanism is not yet fully understood. In this study, we found that B(C6F5)3 is a superior dopant to the other Lewis acids investigated (BF3, BBr3 and AlCl3). Experiments indicate that Lewis acid-base adduct formation with polymers inhibits the doping process. Electron-nuclear double-resonance and nuclear magnetic resonance experiments, together with density functional theory, show that p-type doping occurs by generation of a water-Lewis acid complex with substantial Brønsted acidity, followed by protonation of the polymer backbone and electron transfer from a neutral chain segment to a positively charged, protonated one. This study provides insight into a potential path for protonic acid doping and shows how trace levels of water can transform Lewis acids into powerful Brønsted acids.

Solution-Processed Semitransparent Organic Photovoltaics: From Molecular Design to Device Performance.

Recent research efforts on solution-processed semitransparent organic solar cells (OSCs) are presented. Essential properties of organic donor:acceptor bulk heterojunction blends and electrode materials, required for the combination of simultaneous high power conversion efficiency (PCE) and average visible transmittance of photovoltaic devices, are presented from the materials science and device engineering points of view. Aspects of optical perception, charge generation-recombination, and extraction processes relevant for semitransparent OSCs are also discussed in detail. Furthermore, the theoretical limits of PCE for fully transparent OSCs, compared to the performance of the best reported semitransparent OSCs, and options for further optimization are discussed.

n-Type Ionic-Organic Electronic Ratchets for Energy Harvesting.

Ionic-organic ratchets are three-terminal electronic devices with asymmetric conductivity of the active layer.  These devices  are capable of generating useful direct current electrical power by converting electromagnetic noise signals available in any environment. In this work, we demonstrate for the first time an n-type ionic-organic ratchet which can generate a current of up to 7.29 µA and power up to 12.5 µW that exceed the values reported for many of the presently state-of-the-art, p-type organic electronic ratchets. We show that n-type ratchets require elimination of electron traps at the SiO2 surface, which is not required in p-type devices. This can be achieved by using a trap-free passivation layer such as benzocyclobutene, where the traditional silane treatment is insufficient. Chemical doping is employed to further fill electron traps in the channel and increase carrier concentration and mobilities. Scanning Kelvin probe force microscopy studies provide evidence of a pn-like rectifying junction in the n-type ratchets fabricated in this work, which inherently differs from the rectification mechanism of previous ionic-organic p-type ratchets.

Solution-Processed Ion-Free Organic Ratchets with Asymmetric Contacts.

Ion-free organic ratchets with asymmetric injecting contacts (AICs) are fabricated using solution-processable organic semiconductors. Scanning Kelvin probe microscopy analysis reveals that the rectifying function is achieved via the "charge pump" mechanism. Electrical characterizations show that the device can readily operate under industrial standard radio frequency and its high-frequency performance may be enhanced through further material/device engineering. The built-in asymmetric feature exempts the devices from the complicated material design, device processing, and performance decay associated with the use of ion/semiconductor blends in ionic-organic ratchets. Thus, the AIC ratchets can deliver a persisting ratchet effect and have excellent material compatibility toward organic semiconductors.

Fine Art of Thermoelectricity.

A detailed study of hitherto unknown electrical and thermoelectric properties of graphite pencil traces on paper was carried out by measuring the Hall and Seebeck effects. We show that the combination of pencil-drawn graphite and brush-painted poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS) films on regular office paper results in extremely simple, low-cost, and environmentally friendly thermoelectric power generators with promising output characteristics at low-temperature gradients. The working characteristics can be improved even further by incorporating n-type InSe flakes. The combination of pencil-drawn n-InSe:graphite nanocomposites and brush-painted PEDOT:PSS increases the power output by 1 order of magnitude.

Influence of Radiation on the Properties and the Stability of Hybrid Perovskites.

Organic-inorganic perovskites are well suited for optoelectronic applications. In particular, perovskite single and perovskite tandem solar cells with silicon are close to their market entry. Despite their swift rise in efficiency to more than 21%, solar cell lifetimes are way below the needed 25 years. In fact, comparison of the time when the device performance has degraded to 80% of its initial value (T80 lifetime) of numerous solar cells throughout the literature reveals a strongly reduced stability under illumination. Herein, the various detrimental effects are discussed. Most notably, moisture- and heat-related degradation can be mitigated easily by now. Recently, however, several photoinduced degradation mechanisms have been observed. Under illumination, mixed perovskites tend to phase segregate, while, further, oxygen catalyzes deprotonation of the organic cations. Additionally, during illumination photogenerated charge can be trapped in the NH antibonding orbitals causing dissociation of the organic cation. On the other hand, organic-inorganic perovskites exhibit a high radiation hardness that is superior to crystalline silicon. Here, the proposed degradation mechanisms reported in the literature are thoroughly reviewed and the microscopic mechanisms and their implications for solar cells are discussed.

Raman spectroscopy of Cu-Sn-S ternary compound thin films prepared by the low-cost spray-pyrolysis technique.

Cu-Sn-S (CTS) thin films were deposited onto bare and molybdenum (Mo) coated glass substrates by means of the spray pyrolysis technique under different conditions. The CTS thin films obtained are shown, by means of Raman spectroscopy, to consist of two main phases: Cu2SnS3 and Cu3SnS4 as well as of the secondary phase of Cu2-xS. The electrical conductivity of the spray-deposited p-type CTS thin films under investigation is determined by two shallow acceptor levels: Ev+0.07 eV at T<334 K and Ev+0.1 eV at T>334 K. The material of the CTS thin films was established to be a direct-band semiconductor with the bandgap Eg=1.89 eV. The SEM and x-ray energy dispersive analysis show the surface and cross section of the CTS thin film deposited onto molybdenum-coated glass ceramics substrate with the actual atomic ratios of Cu:Sn:S being 2.9:1:2.64, which is in good agreement with the Raman spectra. Also, a small content of residual Cl atoms was found in the CTS thin films under investigation as the by-product of the pyrolytic reactions.

11th International Conference "Correlation Optics": Propolis films for hybrid biomaterial-inorganic electronics and optoelectronics.

We report on the analysis of optical, polarimetric, and electrical properties of propolis films and hybrid biomaterial-inorganic heterojunctions based on them. It was shown that the material of the propolis films belongs to wide-bandgap optically active substances with the light-scattering centers, which possess complex optical properties. The values of the specific resistance ρ(P)=1.9·107 Ω·cm and dielectric constant ε(P)=19.5 of the propolis film were determined from the spectral distribution of the real and imaginary components of its impedance at room temperature, respectively. The dominating current transport mechanisms through the hybrid bioinorganic heterojunction propolis/p-CdTe were established to be the interface-states-assisted generation-recombination within the depletion region via deep energy levels at forward bias as well as the leakage current through the shunt resistance at reverse bias.